specifications features micro controller ?? fuji's upgraded z-series control- ler incorporating a micro processor, provides the digital communication and high speed operation cycle (100 ms). it is ideally suited for small scale plant or small scale fa (factory automation). 1. unique 2-size micro controller (48 96mm, 96 96mm) rs-485 digital communication has been realized with these 3-size controllers. 2. high controllability high speed operation cycle (100 ms) his been attained. 3. pid auto-tuning function pid parameters can be automatically computed and set by the controller. 4. dust/drip-proof front panel front panel of dust/drip-proof construction conforms to iec ip55 standards. 5. multi-input, programmable range several inputs can be handled by a single controller. 6. full variety of operation and alarm functions various operations and alarms are possible due do the multiple input/output functions. 7. full variety of control types inverter control type, position feedback control type and dual control type are available for selection according to final control devices. 8. wide range of power supply the controller operates on power sources within the range of ac 85 to 265v. 1. control operation functions (1) pid control: proportional band (p): 0 to 3276% (on- off operation of controller with dead band at p=0) integral time (i): 0.1 to 3276 sec derivative time (d): 0 to 900sec (2) pid auto-turning (3) operation cycle: 100 msec (operation cycle is variable within the range of 0.1 to 3276 sec) (4) input filter: setting range: 10.0 to 900.0 sec (set to 10.0 sec prior to delivery) (5) square-root extraction (router): in differential pressure conversion, the flow rate is treated as ??by the router cut point. (cut point is ?nused?prior to delivery.) (6) input shift function: shift of actual measured value (pv) is possible by this function. (7) intermittent pid control: control cycle and control with/without cycle can be designed without changing 100 msec (normal) of operation cycle. (8) non-linear gain: a function to make a gain non-linearity by reducing the gain in the vicinity of set value (sv). data sheet pyh micro controller h pyh9 pyh5 date EDS11-109E oct. 28, 2003
2 pyh 2. table of input/output specifications and alarm output 3. setting and indication (1) accuracy: 0.2% fs, 1 digit temperature compensation: 1 c (2) remote setting input accuracy: 0.2% fs (3) setting method: key switch (4) indicating method: 7-segment led, 4 digits 2, mode indi- cation (led lamp) 4. power failure backup set point values and pid parameters are stored in non- volatile memory for automatic re-start 5. status function self-diagnosis using watchdog timer 6. digital communication function universal interface: ps-485: used for pyh5 and pyh9 as an option. type fixed set inverter con- position feed- dual control item rating point control trol type back control type type type (pyh5, 9) (pyh9 only) (pyh5, 9) (pyh5, 9) input (measured value) thermocouple, resistance bulb, voltage, ???? current with transmitter power supply dc 4 to 20ma (pyh9 only) ? mv input: leak current: 3 a control relay contact ac 220v, 3a (resistive load), 1c contact ? ? output 1 current dc 4 to 20ma, load resistance 600 ? or less ? ? ssr/ssc drive dc 10 to 27v at on, 0.5v dc or less at off, ? ? max. current dc 20ma. motor-driven ac 200v, 3a (resistive load), 1a contact 2 ? value operation control relay contact ac 220v, 3a (resistive load), 1c contact ? output 2 current dc 4 to 20ma, load resistance 600 ? or less ? (dual control ssr/ssc drive dc 10 to 27v at on, dc 0.5v or less at off, ? type only) max. current dc 20ma. auxiliary analog dc 1 to 5v, input resistance 1m ? or more ???? valve position 100 to 1000 ? , 3-wire potentiometer ? digital 1 contact, dc 24v, 15ma (r-ack or sv selec- ???? tion digital 2 ditto (ex-mv command) ???? digital 3 ditto (pyh9 only) (cas-sv) ???? pv/sv/mv dc 1 to 5v, input impedance of connected transmis- analog device 500k ? or more ???? sion output auxiliary digital 1 dc 30v, 0.1a, 1a contact (pyh5: opencollector, ???? alarm dc 30v, 0.1a) output digital 2 ditto (pyh9 only) ???? digital 3 ditto (pyh9 only) ???? main alarm output ac 220v, 1a, 1a contact 2 ???? heater break alarm output ac 220v, 1a, 1a contact (pyh5: opencollector, ? ? dc 30v, 0.1a) fault output dc 30v, 0.1a, 1a contact ???? auxiliary output 7. operation mode remote mode operation, auto mode operation, manual mode operation 8. alarm functions (1) main alarm: absolute value upper/lower limit, devia- tion upper/lower limit, absolute value lower limit with lower limit hold, devia- tion lower limit with lower limit hold, de- viation upper/lower limit with lower limit hold, deviation upper/lower limit. (2) heater break alarm: alarm output with connection to sepa- rate-ly installed current transformer (ct). (3) auxiliary alarm/limiter: measured value upper/lower limit, mani- pulated output upper/lower limit, set point value upper/lower limiter, manipu- lated output upper limiter ............................................................................................................................... ....................................................
3 p y h 12345678 910111213 5 9 a b c d e f g 1 2 3 4 0 1 2 3 0 1 - 2 3 y r y a b c a b c y a b c size of front panel 48 96mm 96 96mm control functions fixed set point control type fixed set point control type (sv select type) inverter control type (sv select type) pyh9 only position feedback control type position feedback control type (sv select type) dual control type dual control type (sv select type) control output 1 relay contact output ssr/ssc drive output dc 4 to 20ma output pulse output (position feedback control type only) control output 2 (dual control type only) none relay contact output ssr/ssc drive output dc 4 to 20ma output size of front panel 96 96mm size of front panel 48 96mm additional specifications 1 none with heater break alarm (control output, relay contact output only) digital communication function none with rs-485 additional specifications 2 none with external set value input (5th digit b, c, e, g not acceptable) with external transmission output a + b (5th digit b, c, e, g not acceptable) input specification type mv/resistance bulb/thermocouple multi-input type dc 1 to 5v/dc 4 to 20ma multi-input type dc 4 to 20ma input type with transmitter power supply (5th digit c: inverter control only) digital output none do1 do1-2 pyh9 only do1-3 description } code symbols 9. operating and storage conditions (1) allowable ambient temperature: 10 to 50 c (2) allowable ambient humidity: 90% rh or less (no condensation) (3) storage temperature: 10 to 70 c 10. general specifications (1) power supply: 100( 15%) to 240(+10%)vac, 50/60hz (2) power consumption: approx. 30va (ac 220v) (3) dielectric strength: power terminal to ground : 1500vac 1min. power terminal to relay contact output : 1500vac 1min. grand to relay contact output : 1500vac 1min. others : 500vac 1min. (4) insulation resistance: 20m ? or more (at dc 500v) 11. structure (1) installation: panel flush mounting (2) enclosure case: plastic housing (3) outline dimensions (4) protective structure: front panel, iec ip55 terminal, iec ip00 (5) finish color: munsell n 1.5 (black) (6) terminal: compression type terminal (awg 14) 12. scope of delivery controller, mounting bracket operation manual (5) life of output relay: mechanical, 10 7 operations (100 on- off operations/min) electrical, 10 5 operations (20 on-off operations/min at rated load) type outline dimensions (h w d) mass (weight) pyh5 96 48 150mm approx. 0.5kg pyh9 96 96 150mm approx. 0.8kg iec (din standards)
4 pyh pyh9 (96 96mm) pyh5 (48 96mm) note 1) panel thickness: 1 to 8mm note 2) permanent sidewise installation is possible. for vertical installation, a minimum space for installation the bracket should be provided as shown in the above diagram. note 3) when a device with extensive depth is installed on both sides of the controller, allow a space of more than 30mm. note 4) install the fan in the permanent pyh5 installation. flt sv/mv a/m sel data ent pv sv mv r a mc1c2h lhb c 96 12 150 10 115 note 3) panel cutout 30 note 3) 30 min.100 min.116 +0.8 0 92 92 +0.8 0 sv/mv a/m sel dat ent pv sv mv c 48 12 150 10 115 96 2 min.55 min.116 40 9 15 10.5 2.5 10 25 7 7.5 30 30 note 3) 30 < permanent installation > panel cutout accessory(ct) note 3) 30 30 30 30 15 2.8 21 40 40 m3.depth 4 2.36 note 3) note 3) quantity 34 56 93 a 141 189 237 285 12 5.8 3.5 current transformer for heater break alarm heater current: for 20 to 50a type: ctl-12-s36-8f heater current: for 1 to 30a type: ctl-6-s-h +0.8 0 92 +0.8 0 92 a +0.8 0 45 +0.6 0 outline diagram (unit:mm)
5 pyh9 connecting terminal no. varies with types. connect terminals in reference to the terminal nameplate attached to the body. note 1) power fuse is not installed in the controller. it should be connected exteriorly. 2) ensure g terminal is connected to the ground. 3) do not use open terminals. 4) connect thermocouple, resistor tube, potentiometer input signal directly to pyh. pyh5 with transmitter power supply 5 6 + 1 a b b 2 3 4 5 6 7 8 9 10 11 15 16 17 18 19 20 21 22 23 31 30 29 28 27 26 25 24 27 28 30 25 27 28 30 32 33 34 35 36 37 38 39 12 13 14 trx1 trx2 shld pv1 pv2 pv3 cas ao g do2 do3 dio common dio common auxiliary di3 auxiliary alarm 3 auxiliary alarm 2 ac ac + shield + + + + + + digital communication rs485 input signal (pv) (min) (max) io ct input power source ground potentiometer for position feedback sc/ /ct + /ct 0 d 3 d 2 d 1 do1 flt almc hb c2c c2o c1c c1 common c2 common control output 1 (relay contact output) control output (position feedback type) control output 1 dc 4 to 20ma or ssr/ssc drive output control output 2 dc 4 to 20ma or ssr/ssc drive output open close common control output 2 (relay contact output) main alarm 1 output main alarm 2 output heater break alarm auxiliary alarm 1 fault output auxiliary di1 auxiliary di2 c1o sc alm2 alm1 external set value input external transmission output (ac85 265v) 1 2 3 4 5 6 7 8 9 10 11 trx1 trx2 shld pv1 pv2 pv3 cas ao 18 19 21 16 18 19 21 12 13 14 c1o sc c1c c2o c2c g ac ac + + ++ + + + power source ground shield flt hb dio common auxiliary di2 auxiliary di1 auxiliary alarm output heater break alarm alm common alarm 2 output alarm 1 output fauit output alm2 alm1 do1 c2 common c1 common control output 1 (relay contact output) control output 2 (relay contact output) control output (position feedback type) control output 1 dc 4 to 20ma or ssr/ssc drive output control output 2 dc 4 to 20ma or ssr/ssc drive output open close common 20 21 22 23 19 18 17 16 15 24 25 26 27 28 29 30 sc/ (min) /ct + (max) + /ct 0 0 d 1 d 2 (ac85 265v) digital communication rs485 a b b input signal (pv) external set value input external transmission putput potentiometer for position feedback ct input connection diagram
pyh information in this catalog is subject to change without notice. printed in japan head office 6-17, sanbancho, chiyoda-ku, tokyo 102-0075, japan http://www.fesys.co.jp/eng sales div. international sales dept. no.1, fuji-machi, hino-city, tokyo, 191-8502 japan phone: 81-42-585-6201, 6202 fax: 81-42-585-6187 http: //www.fic-net.jp/eng caution on safety *before using this product, be sure to read its instruction manual in advance.
|
